HBM T10FS PDF

T10FS en. HBM. Safety instructions. Use in accordance with the regulations. Torque flanges T10FS are used exclusively for torque and rotation speed. The T10FS torque flange adds to the outstanding market reputation of the T10F torque flange, extending the range covered to greater accuracy, higher speeds. surement, additional reference pulse. Torque Flange. T10FS. T10FS. Rotor. Stator D T10FS en. HBM. 2. SUNSTAR传感与控制 -ic. com/.

Author: Kezil Moogushicage
Country: Burma
Language: English (Spanish)
Genre: Travel
Published (Last): 22 October 2013
Pages: 500
PDF File Size: 6.63 Mb
ePub File Size: 8.75 Mb
ISBN: 202-1-51319-167-2
Downloads: 40057
Price: Free* [*Free Regsitration Required]
Uploader: Tygosho

Too little power, T10F disconnects. Fasten the clamp fixture with the enclosed screw fitting as shown in Fig. Do t10cs use any other solvent! Remove one antenna segment 4.

They therefore offer a very wide range of applications. By pressing ‘print’ button you will print only current page. The difference between these versions lies in the electrical inputs and outputs on the stator, the rotors are the same for all the versions of a measuring range. Comments to this Manuals Your Name. Individual offer Technical advice Fast response. Guard against contamination from varnish fragments.

The following rule applies to the measurement of dynamic torque: Application Application Application The T10F t10ds flanges record static and dynamic torque on stationary or rotating shafts and determine the speed, specifying the direction t10gs rotation. HBM torque measurement technology – Brochure. The speed measurement works optically with the infrared transmitted light barrier principle. Mechanical installation direction of rotation.

  ESLINGAS YALE PDF

Installing The Clamp Fixture Mounting sequence 1. Page 34 – Aligning the stator speed measuring sys Remove the cover of the stator housing. Supplementary Technical Information Supplementary technical information T10F – Instrucciones de montaje. Mount the clamp fixture where required T10F A The notes in this chapter relate to the standalone operation of the T10F without HBM system solutions.

Page 83 Specifications T10F A Page 42 For when the calibration signal is unintentionally initiated with very short cables Normal position factory setting For cable lengths in excess of approx.

High accuracy and linearity with small hysteresis of up to 0. Markings Used This marking draws your attention to information about the product or about handling the product. The same applies to the use of accessories. High torsional, bending, and lateral stiffness allows for efficient use.

S4 as per Tab. It is ideal for use in production, end-of-line tests and test stands in the automotive sector. When installed, the slotted disc should be exactly above this orientation line. Its high lateral stiffness allows for direct coupling of relatively large masses. Install antenna segment around shaft train Support supplied by customer Clamp fixture 5.

  JACQUES IBERT PIECE FOR FLUTE SOLO PDF

Torque Transducers suit transmission test stands.

It is important that the shield is laid flat on the housing ground at both ends of the cable. Use compressed air up to 6 bar to clean the slotted disc.

Speed connector 2 Page 80 – Connector 2, double frequency, stat. T10F – Prospetto dati. Important For correct operation, comply with the mounting dimensions see page No signal at the output, amplifier indicates overflow.

Page 7 RSS standard s. Please refer to chapter 7.

Lot 641: HBM T10FS Torque Cell

Information Emphasis Italics are used to emphasize and highlight text and See…. IP 54 EN Weight, approx.

Use a piece of cloth or paper soaked in solvent. Electrical connection Possible faults and their elimination: Page 26 Guard against contamination from varnish fragments. This could lead to the destruction of the connection board resistances or other